An interesting question might be "Has anyone successfully connected an external Zip drive to a machine with two devices already on the secondary IDE channel?". It also has a pass through which allows you to connect a printer to the Zip drive so you can still use your printer.Īpparently, an external Zip drive is hardwired to access the secondary IDE port with no option to change. I am using installation software release 2.8 and the supplied Zip cable.Īn external parallel port Zip drive attaches to the computer's external parallel (printer) port with a parallel cable. One thing I did not mention is this is a 250mg Zip drive, so it requires Win95 at a minimum. It was offered as new but opened so I needed to check it out. The drive installed as the next available drive letter.Īt least I got past the point I needed to see, which was this is a functioning drive. This could be because the software is only valid up to Windows 2000. I connected the Zip drive to a Windows XP machine with only one drive on the secondary channel and I was able to install and use the drive, although there were some errors. Therefore it cannot be used on a machine which already has two drives on the secondary channel. The external drive has no master/slave selector and appears to install to the secondary slave with no other option available. Internal ATAPI Zip drives are set up exactly like hard drives in that you can select master/slave and connect to either the primary or secondary IDE port. Unfortunately, the manual is only for an internal Zip drive and never mentions anything about parallel Zip drives. I got a chance today to look through the online manual that came with the drive. On the other hand, if your drive IS an external ATAPI ZIP and it IS connected to the parallel port I guess the next question would be: how is your parallel port configured? SPP, EPP, ECP or ECP + EPP? More than one person has connected one interface to the other port, usually with severe consequences. The external ZIP SCSI and parallel cables both 25-pin D-SUB, but they differ in gender. So: if your external drive is a "parallel" interface, the first question is whether you're connecting it to a parallel (printer) port. The ATAPI drives had a 40-pin female connector that was pin-compatible with the IDE interface, but - significantly - not all IDE implementations can handle ATAPI, which is a subset of SCSI, actually. There are also internal ZIP drives that utilized SCSI and some that used ATAPI. A floppy drive will appear in Windows explorer.To my knowledge there are ZIP external drives that were made to attach to an USB port, ones that were made to attach to a parallel port, ones that were made to attach to a SCSI adapter and ones that were made to attach to either a SCSI adapter or a parallel port. The device should now be installed and working: Windows will detect the NEC device and a X1DE-USB as well. Now select the "NEC Systems" "NEC USB Floppy". Select the option to list all known devices. Right-click it and choose "Update Driver Software".Ĭhoose that you want to browse your computer for drivers.Ĭhoose that you want to pick from the list of existing drivers. ![]() You'll see the non-working floppy drive (disregard the usb data bar thingy). Go into the System configuration applet (control panel->system, switch to classic view if needed), and open the device manager Windows will complain about needing drivers click cancel. This worked we're going to install the drive as a NEC USB floppy drive. After unsuccessfully trying to get other Windows versions to accept the inf file, I instead tried to find another, similar, device that's supported by Windows out of the box and uses the driver. ![]() ![]() It just tells Windows which operating systems are supported and to use the usbstor.sys driver. I found out how to do this by looking at the. I'm not sure about other versions of Windows the standard 32 bit version of XP professional doesn't work with this method (it doesn't offer a fitting substitute driver, so the original Iomega driver is still needed). Iomega officially only supports Windows XP (32 bit) for this drive (Citizen X1-DE-USB), but with this procedure I got it to work both the 32 and 64 bit versions of Windows Vista. Getting an Iomega USB floppy disk drive to work in unsupported Windows versions
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |